0 Cart
Added to Cart
    You have items in your cart
    You have 1 item in your cart
    Total
    Check Out Continue Shopping

    M65 Sapphire - Installation

    Sink or Countertop Installation

    Things You May Need: adjustable wrench, arc-joint pliers, #2 Phillips screw driver, bucket, towels, safety goggles, flashlight
    Plug your sink drain(s) so that no small parts will go down the drain if you drop them.
    Your M65 faucet is designed for hole size 1.25” to 1.5” diameter. The spout swivels 360 degrees and allows the lever handle and diverter handle to be positioned where you choose. The wand can be mounted where you choose in relation to the spout. Minimum 4” distance between centers is recommended for clearance between the spout and the wand. See example installations.
    • If not already in place, insert the O-ring into the groove in the bottom face of the threaded escutcheon.
    • Insert all three hoses and the mounting tube down through the hole you have selected for installation in your sink/countertop.
    • Place the black rubber or white plastic washer and the steel support ring (washer first) over all three hoses and slide the washer and support ring up over the mounting tube.
    • Partially thread both screws into, but not through, the mounting tube nut.
    • Place the mounting tube nut around all three hoses by passing the hoses through the slot in the mounting tube nut.
    • Screw the mounting tube nut onto the mounting tube and snug firmly to the under surface of the sink/countertop.
    • Tighten the two mounting nut screws securely and evenly. Do not apply undue pressure.
    • Remove the label that is retaining the rubber gasket in the check valve housing assembly - keep the rubber gasket in place in the check valve housing.
    • Screw the check valve housing assembly onto the accessory hose fitting. Hand-tighten only ~ do NOT twist the hose. Hold the hose fitting with pliers to prevent hose twist. This is a straight thread; once you feel solid resistance STOP.
    • Insert the hose guide into the smooth side of the non-threaded escutcheon. Press until the shoulder on the hose guide is tight to the face of the escutcheon. If the surface on which you are installing your faucet is more than 1.3” thick screw the extension ring and the extension tube fully onto the hose guide.
    • If not already in place, insert the O-ring seal into the groove in the bottom face of the escutcheon.
    • Insert the assembled hose guide down through the hole you have selected in the sink/countertop.
    • Screw the hose guide nut onto the hose guide and snug firmly to the under surface of the sink/countertop. If you installed the extension tube in the previous step, install up to three extension spacers as needed before screwing the hose guide nut onto the extension tube.
    • Insert the free end of the black hose down through the hose guide and seat the wand in the hose guide
    Take care in the next three steps to route the black hose and the detergent tube so that they are free to move up and down when the wand is in use. Do not loop around water supply lines or drain pipes.
    It will be helpful to apply dish detergent (to act as a lubricant) to the surfaces to be attached in the next three steps.
    • Insert the free end of the copper hose tube into the small hose section approximately 3/4".
    • Press the large hose section fully onto the barbed end of the check valve housing.
    • Place the detergent tank assembly in a convenient location under the sink. Press the free end (with spring) of the clear plastic detergent tube over the rigid tube of the detergent tank assembly approximately 3/4". See additional instructions included with the detergent tank. Avoid crimping or placing objects on the clear plastic detergent tube as doing so will prevent the flow of detergent.
    Before you connect the flexible supply hoses it is important to flush the water pipes
    • Use an old supply hose to reach from the shut-off valve to a bucket. Put the end of the supply hose into the bucket. Fully open the shut-off valve and allow water to flow until foreign matter no longer comes out ~ at least 15 seconds. Close the shut-off valve. Repeat the procedure with the other shut-off valve.
    Use extreme caution to avoid kinking and twisting the supply hoses. The hoses must not be taut after installation. If your installation requires that you coil the supply hoses to obtain a good connection, maintain an inside diameter of at least 3”.
    • Attach the cold water supply hose (blue stripes) to the cold water shut-off valve. Hold the hose ferrule with pliers to prevent hose twist while tightening the compression nut. Tighten only enough to seat the gasket.
    • Attach the hot water supply hose (red stripes) to the hot water shut-off valve. Hold the hose ferrule with pliers to prevent hose twist while tightening the compression nut. Tighten only enough to seat the gasket
    • Unscrew the aerator assembly from the end of the spout. Be certain to remove the black gasket along with the aerator. It will sometimes stick to the spout end rather than come off with the aerator.
    • Place the faucet lever handle in the off (closed) position.
    • Gently open the cold water shut-off valve. Examine the cold water supply hose and fittings to make sure there are no leaks. If there is a leak, tighten the fitting(s) enough to stop the leak. Repeat for the hot water side.
    • Slowly open the faucet lever handle. It is not unusual for air or air/water mixed to come out until the water lines completely fill with water. Fully open the lever handle. Allow the water to run until the air is out of the lines and foreign matter has flushed from the lines.
    Be sure to run BOTH the hot and cold water for at least 15 seconds. Close the faucet lever handle.
    • Check again for leaks.
    • When all is well, re-attach the aerator assembly with gasket. The aerator is adjustable +/- 10° in all directions so that you can aim your water stream. Simply move the bottom of the aerator with your fingertip.
    • Your new Dishmaster Faucet is ready to use. Please see the Operation section of the manual.
     
     
     
    Back to the top